Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Metal Roof Installation Cost in Dallas?
Metal roof installation in Dallas typically runs between $18,500 and $48,000 for a standard 2,000-square-foot home in 2026. Most homeowners pay around $31,000 for a standing seam steel roof, which breaks down to roughly $9.25 to $24 per square foot installed. Architectural metal shingles land in the middle, while premium copper or zinc systems can push past $75,000.
The range is wide because Dallas roofing conditions vary block by block. A low-slope ranch in Casa View has different underlayment requirements than a two-story Tudor in Lakewood with six dormers and a steep 8/12 pitch. What you’re paying for is the metal itself, the labor to install it correctly, and the fasteners and flashing that keep Dallas hail and wind from turning a 30-year roof into a 10-year headache.
Metal Roof Installation Cost Breakdown (2026)
Here’s what a metal roof costs in Dallas, broken down by roof type and material. These numbers reflect the 2026 Dallas market and include labor, materials, underlayment, and basic flashing for a typical single-family home of about 2,000 square feet.
| Roof Type | Material Cost (per sq ft) | Installed Cost (per sq ft) | Typical Total (2,000 sq ft home) |
|---|---|---|---|
| Corrugated steel panels | $3.50 – $6.00 | $7.50 – $11.00 | $15,000 – $22,000 |
| Standing seam steel (24-gauge) | $5.50 – $9.50 | $12.00 – $18.00 | $24,000 – $36,000 |
| Stone-coated steel shingles | $6.00 – $9.00 | $11.00 – $16.50 | $22,000 – $33,000 |
| Aluminum standing seam | $5.00 – $8.00 | $11.50 – $17.00 | $23,000 – $34,000 |
| Copper (standing seam) | $18.00 – $28.00 | $30.00 – $45.00 | $60,000 – $90,000 |
| Zinc (standing seam) | $14.00 – $22.00 | $25.00 – $38.00 | $50,000 – $76,000 |
Those are the material and labor costs. But a full metal roof replacement in Dallas almost always includes a few additional line items. Here’s what else gets written into the estimate:
- Old roof tear-off: $1.50 to $3.50 per square foot. If your existing shingle roof has two layers, the top layer alone can weigh 500 pounds per 100 square feet, which means more labor and higher disposal fees.
- Decking repair: $2.00 to $4.50 per square foot for any rotted or hail-damaged sections. In East Dallas neighborhoods like Forest Hills and Little Forest Hills, mature oak trees drop branches that puncture decking more often than homeowners expect.
- Underlayment upgrade: $0.80 to $2.00 per square foot for high-temp synthetic underlayment, which holds up better under a metal roof than standard felt when attic temperatures climb past 130°F in July.
- Flashing: $800 to $3,000 total depending on chimney count, skylights, vent pipes, and valley intersections. Older Dallas homes built before 1980 often have three or more penetrations to flash around.
- Gutter and fascia work: $6 to $14 per linear foot if gutters need replacing alongside the roof. Many Dallas homeowners replace gutters with the roof so fasteners don’t get disturbed twice.
One thing we tell every Dallas homeowner: if a metal roof quote comes in under $12,000 for a 2,000-square-foot home, ask what’s missing. It’s almost certainly using thin 29-gauge steel, skipping the tear-off, or cutting corners on underlayment. In a city that gets golf-ball hail, that’s a false economy.
What Affects Metal Roof Installation Pricing in Dallas
Metal roofing costs move around for six reasons that come up on nearly every Metal Roof Installation in Dallas project we quote:
- Roof pitch and complexity. A 4/12 pitch roof is walkable and straightforward. An 8/12 or steeper roof needs safety harnesses, ladder stabilization, and more labor hours. Dormers, hips, valleys, and turrets add cutting time and wasted material. In Preston Hollow, where rooflines tend toward the complicated, labor can push 40% higher than a simple gable roof in Richardson.
- Existing roof condition and layers. Dallas code allows up to two layers of shingles before a full tear-off is required. If your home has two layers, expect an extra $3,000 to $7,000 just for tear-off and dump fees. If the decking underneath is water-damaged, that adds more.
- Material gauge and coating. 24-gauge steel costs about 20% more than 26-gauge but resists hailstones considerably better. Galvalume coating adds $1 to $2 per square foot over galvanized and holds its color longer in Dallas’s UV-heavy sun. Stone-coated metal shingles cost more than standing seam but less than copper.
- Roof size. This one’s simple: more square footage, more metal. But there’s also a mild economy of scale. A 1,200-square-foot roof in Oak Cliff might cost $13 to $19 per square foot installed, while a 3,500-square-foot roof in Frisco might drop to $10 to $15 per square foot because the crew’s mobilization cost spreads thinner.
- Access and yard conditions. If the crew can’t park a trailer near the house, if the backyard is fenced with no gate wide enough for a dump trailer, or if power lines run close to the roofline, expect access fees. Homes in Kessler Park with tight driveways and mature landscaping frequently incur $500 to $1,500 in access-related charges.
- Time of year. Fall and spring are the busiest roofing seasons in Dallas. Summer is slower but hotter, which slows crews slightly. Winter brings more unpredictable pricing. We don’t surge-price, but some Dallas contractors do. You’ll get a written price that stays written, regardless of the month.
Metal Roofing vs. Asphalt Shingles: Dallas Cost Comparison
Homeowners frequently ask whether a metal roof is worth the premium over architectural asphalt shingles. Here’s the straight comparison for a typical 2,000-square-foot Dallas home in 2026:
- Asphalt architectural shingles: $9,500 to $14,500 installed (GAF Timberline, CertainTeed Landmark, or Owens Corning Duration class). Life expectancy: 18 to 25 years in Dallas heat and hail. May need replacement after one or two severe hail seasons if you’re under-insured.
- Standing seam metal: $24,000 to $36,000 installed. Life expectancy: 40 to 60 years on the roof deck, with fastener and coating maintenance at the 20-30 year mark. Class 4 impact rated, which most Dallas insurers recognize with premium discounts of 8% to 28%.
- Stone-coated steel shingles: $22,000 to $33,000 installed. Life expectancy: 40 to 50 years. Looks like a shingle roof from the street, carries Class 4 hail rating, and avoids the “barn roof” look some HOAs dislike.
The break-even point works like this: if you plan to stay put for 15 years or more, metal usually wins over two asphalt replacements. If you’re selling in five years, asphalt wins on upfront cost, though a metal roof does add resale appeal in a city where every hailstorm sends the neighborhood into tarp mode. Grant Whitlock, owner at Mercer Roofing Co Dallas, walks every estimate through both scenarios so you’re comparing real dollars, not marketing claims.
Does Metal Roofing Hold Up to Dallas Hail and Wind?
Short answer: yes, with the right gauge and installation. Dallas sits in hail alley. The National Weather Service recorded 19 significant hail events in Dallas County between 2019 and 2025, with stones over two inches falling in Oak Cliff, Garland, and Mesquite. A 24-gauge standing seam steel roof with a Class 4 impact rating shrugs off most of what Dallas skies throw at it. That’s why so many insurers discount metal roofs here.
But the metal is only half the story. Hail dents are cosmetic on most gauges. The real damage comes from wind-driven rain getting past badly lapped panels, undersized fasteners, or flashing that wasn’t sealed to Dallas’s frequent freeze-thaw cycles. We’ve torn off five-year-old metal roofs in Arlington where every leak traced to fasteners backed out because the original installer used the wrong neoprene washers for Texas heat. The metal was fine. The installation was not.
Wind resistance matters too. Dallas is in a region where straight-line derechos and tornado-warned supercells are part of life. A properly installed standing seam roof with concealed fasteners carries a wind rating up to 140 mph when the panel clips match the engineering table. Exposed fastener panels are typically rated lower, around 90 to 110 mph, because the screws sit proud of the surface.
Metal Roof Materials Dallas Homeowners Actually Choose
Across the home roofing projects we complete in the Dallas metro, three material types account for the large majority of metal roof installs:
Standing Seam Steel (24-Gauge)
The most common metal roof we install in Dallas. Concealed fasteners, clean vertical lines, and the highest wind rating of the common systems. Available in 30+ colors. White and light gray hold up best under Dallas’s 230+ sunny days per year, reflecting heat instead of absorbing it. Cost: $12 to $18 per square foot installed.
Stone-Coated Steel Shingles
A good fit for HOAs in North Dallas, Plano corridor, and McKinney that restrict standing seam profiles. Stone-coated shingles mimic the look of architectural asphalt but carry steel underneath. The stone coating adds impact resistance and sound dampening. Cost: $11 to $16.50 per square foot installed.
Aluminum Standing Seam
Lighter than steel and immune to rust, which makes it a solid choice for homes within five miles of White Rock Lake or the Trinity River corridor where humidity sits higher year-round. Aluminum costs slightly more than steel and dents a bit more easily, but it never rusts at the cut edges. Cost: $11.50 to $17 per square foot installed.
Copper and zinc do appear on Dallas roofs, usually in Highland Park or University Park on architect-designed homes. They’re beautiful and genuinely 100-year materials, but the price is a jump most homeowners don’t need to make. We quote them, and occasionally install them, but we won’t push you toward premium metals just because the margin is fatter.
Is a Metal Roof More Energy Efficient in Dallas?
Yes, and the effect is measurable. A metal roof with a reflective coating rated by the Cool Roof Rating Council reflects 60% to 75% of solar radiation back into the atmosphere. A dark asphalt shingle roof reflects about 10% to 20%. That difference shows up in your attic.
In July, a Dallas attic under dark shingles routinely hits 140°F to 150°F. Under a light-colored metal roof, that same attic typically stays between 105°F and 115°F. That 30-degree delta means your air conditioner runs less, especially in single-story ranch homes where the roof square footage rivals the conditioned floor area below. Homeowners with standing seam metal roofs report summer cooling savings in the 10% to 25% range depending on insulation levels and thermostat habits.
But the roofing component is only part of the energy picture. You get the full benefit when the metal roof is installed with proper attic ventilation, reflective underlayment, and a ventilated air gap that lets heat escape rather than radiating into the decking. Done wrong, a metal roof installed directly over old shingles without an air gap can trap heat. We can walk you through what your specific roof needs before any price gets written down.
How to Save on Metal Roof Installation in Dallas
Metal roofing is an investment, but there are legitimate ways to keep the cost from ballooning without sacrificing quality:
- Get a written price before any work starts. Not a verbal estimate, not a ballpark. Every Mercer Roofing Co Dallas project begins with a written price that includes all line items. If a contractor won’t put it in writing, walk away.
- Time the project for late winter. January and February are the slowest months for Dallas roofers. You won’t get a discount from every company, but crews are more available and you’ll avoid the spring rush that pushes lead times to three or four weeks.
- Check your insurance after a hail storm. If a named hailstorm has hit your zip code in the past 12 months, your roof may qualify for a claim that covers part of the metal upgrade. Most Dallas policies won’t pay the full delta between asphalt and metal, but many will cover the asphalt replacement cost, which you can apply toward the metal total.
- Keep the roof shape simple. If you’re already planning a home addition or remodel, a simple gable roofline costs thousands less in metal than a complex hip roof with valleys. Fewer valleys means fewer weak points and less flashing labor.
- Don’t skip the inspection. A free estimate that includes a full roof inspection costs you nothing and tells you whether you need decking repair, new underlayment, or can install over the existing roof. Call (432) 302-5605 and we’ll send someone out to look.
Metal Roof Installation Timeline in Dallas
Most Dallas metal roof installations take 3 to 7 working days for a standard single-family home. Here’s what the week looks like:
- Day 1: Tear-off (if needed) and decking inspection. We remove the old roof, inspect the decking for hail damage or rot, and replace any bad sections before the underlayment goes down.
- Day 2: Underlayment and flashing. High-temp synthetic underlayment is rolled and fastened. Chimney flashing, valley flashing, and drip edge go down. This is the day that determines whether your roof leaks or not.
- Days 3-5: Panel installation. Metal panels are measured, cut, and locked into place. Standing seam takes longer than exposed fastener because each panel gets crimped and clipped rather than screwed through the face.
- Day 6-7: Ridge caps, final flashing, and cleanup. The crew walks the roof with a checklist, seals every penetration, and runs a magnetic sweeper over the yard twice for dropped fasteners.
Weather can stretch the timeline. A thunderstorm delay in May or June can push a 5-day install to 8. We watch the forecast closely and don’t leave a roof half-open. If rain is coming, the roof gets dried in the same day.
Is DIY Metal Roof Installation Worth It in Dallas?
For most Dallas homeowners, the honest answer is no. Metal roofing is not a weekend project. The panels are large, awkward, and sharp at the edges. Working on a Dallas roof in summer means surface temperatures that hit 160°F and make foot slips common. Falls from residential roofs are one of the most common causes of serious construction injuries nationwide, and metal panels are slicker than shingles whether dry, dusty, or dew-wet.
The mistakes we see from DIY or handyman metal installs in Dallas include: fasteners driven at the wrong angle so the neoprene washers don’t seal; panels lapped the wrong direction for the prevailing wind; underlayment skipped entirely over the old shingles; and flashing that leaks at the first gully-washer. Those “savings” turn into $8,000 repair bills inside two years.
This kind of work is best left to a trained professional. Not because it’s impossible to learn, but because the cost of learning on your own roof is a leaking one. Every Mercer technician arrives background-checked and badged, and the roof they install is covered by a 365-Day Done Right Promise: if it’s not right, we make it right within the year.
Questions to Ask Any Dallas Metal Roofing Contractor
Before you sign anything, ask these six questions. A good contractor answers all of them directly.
- “Will you send me the name and photo of the technician before they arrive?” Mercer does this automatically. You should know who is pulling into your driveway before they ring the bell.
- “Is the price in writing and will it change mid-project?” If the answer is anything other than a firm yes and no, keep looking. Our written price is the final price, period.
- “What gauge of steel are you using?” Demand 24-gauge or 22-gauge for Dallas hail. 29-gauge is too thin for this climate.
- “What kind of underlayment goes under the metal?” The answer should be synthetic or peel-and-stick high-temp underlayment, not 15-pound felt.
- “Do you warranty the workmanship, and for how long?” Ours is 365 days, in writing, on every repair and install. If a roof fails because of our workmanship, we return at no charge.
- “Can I see your license and insurance?” A legitimate Dallas contractor shows both without hesitation.
FAQs – Metal Roof Installation Cost
How much does a standing seam metal roof cost in Dallas?
Standing seam metal roofs in Dallas run $24,000 to $36,000 for a standard 2,000-square-foot home, or $12 to $18 per square foot installed. That price includes tear-off, 24-gauge steel panels, high-temp underlayment, and flashing. For an exact written price on your roof, call (432) 302-5605 for a free estimate.
Is it cheaper to repair or replace a metal roof in Dallas?
Repairing a metal roof is cheaper than replacing it in nearly every case. A minor repair like re-sealing a fastener line or replacing a bent panel costs $350 to $1,200 in Dallas. If more than 25% of the roof is failing or hail has dented most panels to the point of coating damage, replacement starts to make better financial sense. We’ll only recommend replacement when the math actually works.
How much does a stone-coated steel roof cost in Dallas?
Stone-coated steel shingles run $22,000 to $33,000 on a 2,000-square-foot Dallas home, or $11 to $16.50 per square foot installed. They’re a strong middle option for homeowners who want metal durability with an asphalt shingle look. Call (432) 302-5605 for a written quote on your specific roofline.
Does a metal roof in Dallas help lower insurance premiums?
Yes. Many Dallas insurance carriers discount premiums 8% to 28% for Class 4 impact-rated metal roofing, which includes most standing seam and stone-coated steel systems installed in 2026. Ask your insurer for a quote before you choose your material, and we’ll match the system to what your carrier recognizes.
How long does a metal roof last in Dallas?
A properly installed 24-gauge standing seam roof in Dallas lasts 40 to 60 years, with coating and fastener maintenance recommended at the 20 to 30 year mark. Stone-coated steel shingles last 40 to 50 years. The weak point in Dallas is almost never the metal itself, it’s the fasteners and flashing, which is why installation quality matters more than the panel brand.
Can you install a metal roof in Dallas over existing shingles?
Yes, and it’s code-compliant in most Dallas suburbs if there’s only one layer of shingles and the decking is sound. Installing over shingles saves $1.50 to $3.50 per square foot in tear-off and dump costs. But we only recommend it when the decking shows no hail damage or rot. If there’s any question, we pull a section and look. Every Mercer estimate includes a written recommendation either way.
Get a Written Metal Roof Price in Dallas
Pricing reflects the Dallas market as of 2026. Mercer Roofing Co Dallas offers free estimates, and every project begins with a written price before any work starts. The technician who arrives at your door will have already sent you their name and photo, and they’ll carry a photo ID badge at the door, per the Threshold Verified standard we’ve held since our founding in 2000 under the Threshold Group family of home-service companies.
Call (432) 302-5605 and a live person answers, any hour, any day. We’ll schedule a free inspection, give you a written price, and walk you through exactly what your metal roof will cost before you commit to anything.
Pricing reflects the Dallas market as of 2026. Mercer Roofing Co Dallas offers free estimates – call (432) 302-5605.
Written by Grant Whitlock, Owner at Mercer Roofing Co Dallas, serving Dallas since 2000.
What Our Customers Say
"Leak showed up in the hallway ceiling after a big storm. They found the failed pipe flashing in about ten minutes, replaced it, and checked the attic for wet insulation."
- Sophie R."Roofer showed his ID and gave me the crew lead's name before anyone climbed the ladder. Replaced a patch of missing shingles and resealed two vent boots. Written estimate matched the final bill."
- Brian J."Honest inspection. He went up, took photos, and told me I had maybe five more years instead of selling a full replacement."
- Xavier L.