Boral Shingle Repair Nationwide

Boral Shingle Repair: The Dallas Owner’s Guide

Boral shingle repair in Dallas typically runs $340 to $680 for a targeted patch job, and $8 to $14 per square foot when replacement spans a larger section. We stock Boral-compatible shingle repair materials on our trucks and can usually complete a standard repair in one visit. Most Dallas homeowners discover a Boral shingle problem the same way: a dark stain creeping across the ceiling, granules collecting in the gutter, or a shingle flapping loose after a spring storm rolls through from the west. Boral shingles are built differently than standard asphalt, and when they fail, the repair approach matters. Mercer Roofing Co Dallas is an independent roofing contractor, not affiliated with Boral, and we repair these roofs with manufacturer-compatible materials and written pricing before any work starts.

Call (432) 302-5605

Key Takeaways

• Most Boral shingle repairs in Dallas run $340 to $680 installed.
• Boral’s granule-shedding rate in North Texas heat and hail is the most common failure point we see.
• We carry Boral-compatible repair stock and provide a written price before any work begins.
• Every repair is covered by our written 365-Day Done Right Promise.

Which Boral Models This Applies To

Boral’s roofing lines break down into a few families that show up on Dallas homes. The most common on mid-2010s builds are the Boral Concrete Roof Tiles and the Boral Steelstone coated-steel shingles. Steelstone panels interlock on metal battens and use a hidden fastener system, while the concrete line is laid in overlapping courses like traditional tile. On newer construction, you may also see Boral’s StormShield composite shingles, which mimic wood shake or slate but install like a thick asphalt shingle. Each series uses different flashing profiles, different underlayment requirements, and different sealant needs. The compatibility gotcha we run into often: Steelstone panels cannot be swapped with StormShield shingles, even if the color looks identical, because the fastener spacing and interlock geometry differ. The panel or shingle will not seat correctly, and the roof will leak at the seam eventually.

To identify what you have: check the underside or back of a loose piece for a molded or stamped series name, measure the exposed surface, and count the fasteners per piece. We can match it from a photo in most cases. When it comes to OEM versus aftermarket, Boral is one brand where we lean OEM or manufacturer-specified replacement pieces on steel-backed products, because the paint system and metal gauge are engineered as a unit. For concrete tile, high-quality aftermarket tiles from reputable local suppliers in the Dallas market hold up fine, provided the color range and profile match what’s on the roof now.

Signs Your Boral Shingle Repair Is Failing

• Granule loss heavy enough to expose the matrix. Dallas UV exposure and hail wear down the surface granules on Boral Steelstone faster than most climates. When the steel core starts showing through in streaks, corrosion follows within a couple of Texas storm seasons.
• A flapping or rattling panel you can see from the ground. Hidden fasteners can back out over time as the roof deck expands and contracts in Dallas’s temperature swings. The panel looks fine from a distance, but it is loose, and water is getting in under it.
• Water stains on ceilings near exterior walls after a hard rain. This usually points to failed flashing where the Boral roof meets a wall or chimney. Boral roofs use custom step flashing profiles, and a generic flashing repair will not seal correctly against their panel contours.
• Cracked or chipped concrete tiles after hail. Boral concrete tiles are dense and hold up well, but a big enough hailstone will crack the corner of a tile. A cracked tile lets water flow onto the underlayment, which is the roof’s actual waterproof layer, and that layer wears faster when wet.
• Rust streaks or corrosion on Steelstone panels. Once the coating is compromised, the steel beneath reacts fast in humid Dallas summers. We see this on south-facing slopes most often, where the afternoon sun cooks the surface.

Replacement Cost & What’s Included

A focused Boral shingle repair on a Dallas home typically lands between $340 and $680. That covers the failed shingles or panels, matching fasteners, flashing or sealant work at the penetration point, and labor. Larger replacement areas, where a whole roof slope needs re-shingling after hail or wind, run $8 to $14 per square foot. The square-foot price moves based on the material line, roof pitch, and whether the underlayment beneath must also be replaced. If the decking under the Boral pieces has been wet, that is a separate line item you will see on the written estimate before we start. Parts are priced straight, labor is priced straight, and the number on the estimate is the number on the invoice. Every repair carries our 365-Day Done Right Promise in writing: if it is not right within a year, we come back and make it right, and a second visit after a failed repair is free.

DIY or Call Us?

There are things you can safely check from the ground: missing or shifted panels, obvious granule loss, cracked tile corners, and rust streaks. A pair of binoculars and a dry afternoon gives you a useful picture without ever getting on a ladder. What we would not recommend is working on a Boral Steelstone roof yourself. The panels interlock under tension in some courses, the hidden fasteners require the right tool and angle to back out cleanly, and on a pitched roof in Dallas heat, footing goes from solid to dangerous without warning. Concrete tile cracks easily if you step on the wrong spot. If the repair needs to be watertight for the next decade, it is a trained professional’s job. Call us at (432) 302-5605 for a written quote before you spend a weekend on a ladder. Every estimate is free, and every technician who arrives is background-checked and shows a photo ID at the door before stepping onto your property.

FAQs