Boral Gutter Replacement Nationwide

Boral Gutter Replacement: The Dallas Owner’s Guide

We stock and install Boral-compatible gutter replacement parts across Dallas, with most full gutter runs running between $18 and $32 per linear foot installed, depending on profile and total length. If a section of your Boral gutter has pulled away, split at a seam, or is dumping water against the foundation, we can usually match the profile and get it replaced within a few days of the estimate. Most Dallas homeowners discover the problem during a hard spring storm, when water starts sheeting off the corner of the house or pooling near the slab instead of flowing to the downspout.

Call (432) 302-5605

Boral gutters are known for their steel and aluminum profiles, but the recurring failure point we see in Dallas isn’t the gutter itself. It’s the hangers and the seam sealing. North Texas temperature swings run 40 to 50 degrees in a single day during spring and fall, and that repeated expansion and contraction works hangers loose over time. Once a hanger lets go, the gutter sags, water sits, and the seam eventually opens. That’s the part most people are actually replacing, even when they think they need a whole new run.

Which Boral Models This Applies To

Boral gutters come in a few distinct profiles, and matching the replacement correctly matters more than most homeowners expect. We work with 5-inch and 6-inch K-style profiles, which cover the majority of Boral installations in Dallas, plus the half-round profiles found on some custom builds in neighborhoods like Lakewood and Preston Hollow. The key is the profile depth and the lip configuration, which you can check by measuring the opening at the top and looking at the front lip shape. A 6-inch gutter is not just a bigger 5-inch; the hanger spacing required is different, and the outlet sizing has to match or you’re trading one leak for another.

When it comes to parts, we carry both OEM Boral sections where available and quality aftermarket equivalents that match the gauge and profile spec. The honest distinction: OEM matters most on warranty-backed full roof-and-gutter installs, where the manufacturer’s paperwork requires OEM to keep the warranty valid. For a straight section replacement on a 10-year-old house, a same-gauge aftermarket section, properly hung and sealed, performs identically. Boral’s aluminum K-style is typically .027 to .032 gauge, and we match that, not whatever is cheapest on the shelf. Mercer Roofing Co Dallas is an independent service provider and not affiliated with Boral, but we stock and install their profiles daily.

Signs Your Boral Gutter Replacement Is Failing

• Water pouring over the front lip during rain. This almost always means the slope is gone or a hanger has pulled loose from the fascia. In Dallas, the repeated freeze-thaw in February and March loosens fascia screws faster than anywhere else we’ve worked, including the Southwest roofs Grant Whitlock spent his early career on.
• A visible gap at the seam with water streaking the siding below. Seam sealant has a real lifespan, about 5 to 7 years under Texas UV. Once it hardens and cracks, water finds daylight. Replacing the section and re-sealing properly is the fix, not piling on more caulk.
• Gutter pulling away from the roofline. This is the most common failure we see, and it’s not the gutter’s fault. In older Dallas homes, the fascia board behind the gutter has begun to rot from years of overflow, and the hanger screws no longer bite into solid wood.
• Standing water in the gutter days after the last rain. Mosquitoes love it, and so does rust. Boral aluminum won’t rust, but the steel hangers will. Standing water almost always means the outlet is blocked or the slope has settled in the wrong direction.
• A rust line at the outlet connection. That rust is coming from the hardware and screw points, meaning water is sitting around the outlet longer than it should. That is usually a pitch and hanger issue rather than a material failure, and it’s fixable without a full run of new gutter.

Replacement Cost & What’s Included

So what does a Boral gutter replacement actually run in Dallas? For a standard 5-inch aluminum K-style section, installed, with matching hangers and seam sealant, you’re looking at $18 to $26 per linear foot. A 6-inch profile runs $24 to $32 per linear foot. A typical single-story home with about 160 linear feet of gutter is somewhere in the $2,900 to $4,200 range for a full replacement. Prices go up when we’re replacing fascia board first, working on a two-story run, or the old gutters were hung with spacing that requires new hanger points.

Every Mercer Roofing Co Dallas quote is a written price given before any work starts, and it breaks out parts and labor so you know exactly where the money goes. The work itself is covered by our 365-Day Done Right Promise: if it’s not right within a year, we make it right. That’s in writing on every job, not just spoken. No change orders, no surprises on the invoice. You’ll know the number before we touch the ladder.

DIY or Call Us?

You can safely check a few things before calling: look for visible gaps at the seams, tug gently on a few hanger points to see if they’re loose, and watch during the next rain to see where water exits. What we would not suggest is doing the replacement yourself at height. Gutter work means ladders, and gutter work at a two-story roofline means ladders at the exact angle where falls happen. The National Safety Council consistently ranks falls as a leading cause of home injury, and gutters are one of the top places it happens.

What we see go wrong with DIY is the slope. Get it slightly off in either direction, and you’ve built a water trap or a waterfall. Hanger spacing is the other load-bearing issue. It’s not hard once you know the spec, but a sagging gutter on a new install is a waste of time and material. If you’re in Dallas and want it done once, call (432) 302-5605 and we’ll put a written number in your hand before any work starts.

FAQs